Dark Light
-5%
, , ,

Solar Controller 12V/24V 30A 20A 10A Solar Regulator PWM Battery Charger LCD Display Dual USB 5V Output

Availability:

9999 in stock


$81.93 $86.14

  • Brand Name: diymore
  • Origin: Mainland China
  • Condition: New
  • Type: Voltage Regulator

Product features.

1. Solar controller 12V/24V automatic identification, can charge 3 kinds of batteries, lead-acid batteries (12V/24V battery automatic identification), lithium-ion batteries, lithium iron phosphate batteries.

2. Large screen LCD display, adjustable charging and discharging parameters

3. Complete 3-stage PWM charging management.

4. Built-in over-current/short-circuit protection, open-circuit protection, reverse-connection protection, all self-recovery type, no damage to the controller

5. Double MOS anti-backflow circuit, ultra-low heat generation.

Product parameters.

System voltage: 12v/11.1V/12.8v

Rated charging current: 10A, 20A, 30A

Rated discharge current: 10A, 10A, 10A

Maximum PV voltage: 23V at the highest for 12V battery; 46V at the highest for 24V battery

Battery type:

B1=lead-acid battery 12V/24V battery automatically identified

B2=Lithium-ion battery (lithium battery) 3 strings of 3.7V=11.1V

B3=Lithium iron phosphate battery 4 series 3.2V=12.8v

Charge cut-off voltage:14.4V(B1), 12.6V(B2), 14.6V(B3)

Discharge cutoff voltage: 10.7V(B1), 9v(B2), 10V(B3)

Discharge recovery voltage: 12.6V(B1), 10.5(B2), 12V(B3)

Light-controlled light-on threshold: 8V for PV panels (light-controlled light-on delay)

Light control off threshold: PV panel 8V (light control off light with delay)

USB output: 2-way USB output, 5V/2.5A (max)

Standby current: <10mA

Operating temperature: -35+60c

Size: 133.5* 70*35mm

Note: The controller default is B2 charging lithium-ion batteries (lithium batteries) battery type for B2 mode; using lead-acid battery controller battery type please set B1; lithium iron phosphate batteries set to B3. 

Support battery type.

B1 = lead-acid battery 12V/24V (automatic identification)

B2 = lithium-ion batteries (lithium batteries) 3 strings of 3.7V = 11.1V

B3=Lithium iron phosphate battery 4 strings of 3.2V=12.8V

System connection.

1. Connect the positive and negative battery terminals to the controller as shown in the diagram, the controller will automatically detect the battery voltage.

2. Connect the load positive and negative terminals to the controller as shown in the diagram, be careful not to reverse the connection.

3. Connect the solar panel to the controller as shown in the diagram.

Note: Please strictly follow the above order to access, otherwise the controller may be damaged. The disassembly order is opposite to the wiring order.

Suggestions for safe use.

1. The controller is automatically adapted for 12V/24V lead-acid battery. When installing it for the first time, please make sure that the battery has enough voltage so that the controller can recognize it as the correct battery type.

2. Install the controller as close to the battery as possible to avoid the voltage drop caused by the long wire, which will affect the normal voltage judgment.

3. The controller is only applicable to various lead-acid batteries (including open, sealed, gel, etc.), please do not use it for other batteries (including lithium batteries, NiMH batteries, etc.)

4. This controller can only use photovoltaic panels as the charging source, please do not use DC or other power sources as the charging source. 6. This controller will be hot when running, please note that the controller will be installed on a flat, well-ventilated surface.

Product list.

Solar controller x 1

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Solar Controller 12V/24V 30A 20A 10A Solar Regulator PWM Battery Charger LCD Display Dual USB 5V Output”

There are no reviews yet.

0